Carbon side skirts

Discussion in 'Fiesta ST Exterior Upgrades' started by kamakazee, Jan 13, 2014.

  1. kamakazee

    kamakazee Active Member

    Just got these done today. Compliments the carbon front splitter nicely. Probably going to get a couple sets of H&R wheel spacers to widen the stance just a bit :)
    20140113_163555.jpg
    20140113_163420.jpg
     
    Molten ST, Kalil, BlackBird and 2 others like this.
  2. Register or Sign in

    Advertisement Sponsor

     
  3. moshaholic2

    moshaholic2 Active Member

    Thinking of wheels spacers as well. Where did you get the carbon skirts?
     
  4. kamakazee

    kamakazee Active Member

    I got these at Bojix Design. Haro did some measurements and I will be going with 10mm spacers front, and 15mm spacers rear. With the H&R sport springs, the height is perfect now I just need to take care of the width.
     
    Molten ST likes this.
  5. stuntdoogie

    stuntdoogie Active Member

    Hows the ride with the H&R springs? The same bouncy feel or Softer compared to the stock.

    Sent from my SPH-D710 using Tapatalk
     
    Molten ST likes this.
  6. D1JL

    D1JL Well-Known Member

    I have been waiting for those.
    If I had known they were available I would have gone over there yesterday.

    Sent with my retro keyboard and mouse.

    Dave
     
    Last edited: Jan 15, 2014
  7. kamakazee

    kamakazee Active Member

    The H&R springs are fantastic with the 16" wheel combo. The ride is still a little bouncy but more manageable compared to the stock setup. I had the springs installed after I got the 16" wheels installed so it is possible that the ride could be worst with the bigger wheels/ low profile tires setup. The springs have reduced body roll, brake dive and squat during acceleration but only just a bit. Coilovers would provide better performance but my main intentions is to keep this a daily driver that's comfortable. I'd be curious to get feedback from folks who have these springs on 17" or bigger wheels.
     
  8. kamakazee

    kamakazee Active Member

    Mine had to be special ordered and took about a week so I would give Sam or Haro a call before you head over there.
     
  9. BRGT350

    BRGT350 Well-Known Member Staff Member

    the skirts look fantastic!! I am thinking of doing urethane or abrasion resistant plastic underbody protection that would mount the same way as the skirts do. Great work on the skirts with the splitter, very nice design theme.
     
  10. kamakazee

    kamakazee Active Member

    Thank you, sir! After looking at their SEMA Fiesta ST, I knew I had to have them! Underbody protection would be pretty cool, please give us an update if you go through with the project.
     
  11. D1JL

    D1JL Well-Known Member

    I picked mine up today.
    They are real carbon fiber.
    Now to paint them black.

    Sent with my retro keyboard and mouse.

    Dave
     
    Molten ST likes this.
  12. D1JL

    D1JL Well-Known Member

    These are nice pieces and if you leave the carbon fiber look you will be in good shape.
    However if you paint them you will see all the mold imperfections.

    They are very easy to install and it only takes about 30 minutes.
    If you do the install by yourself, you will need 2 small c-clamps (4 if you want to hang both sides at the same time).
    You will also need a drill-driver.

    Sent with my retro keyboard and mouse.

    Dave
     
    CarefreeAZ likes this.
  13. svt3d

    svt3d Member

    who actually makes the skirts, I can't find them on there site???
     
  14. D1JL

    D1JL Well-Known Member

    They are made by Bojix Design at http://www.bojix.com/.
    They are not on their site, just call them.


    Dave
     
    Molten ST likes this.
  15. svt3d

    svt3d Member

    Guess thats what I will have to do...Sucks I was just in Ontario last week I could have ran up there and talked to them!
     
  16. BlueBomber

    BlueBomber Active Member

    What'd they run you?
     
  17. kamakazee

    kamakazee Active Member

    With install, I think I paid about $600.
     
    Molten ST likes this.
  18. D1JL

    D1JL Well-Known Member

    You need to call to get the correct prices.
    I installed them myself.


    Dave
     
    BlueBomber likes this.
  19. charest2394

    charest2394 New Member

    The 600$ is it for the front splitter and the side skirts or just for the side skirts?
     
  20. kamakazee

    kamakazee Active Member

    That is just for the side skirts. The front splitter is finally up on their website but not the skirts.
     
    Molten ST likes this.

Share This Page